Skip to main content

Autel IM608 Pro Program BMW 2011 535i CAS4 a Key by OBD

 

Autel-Im608-Pro-Program-Bmw-2011-535i-Cas4-A-Key-By-Obd-1

Purpose

Using Autel MaxiIM IM608 Pro Programmer to add a new key for 2009-2016 BMW 5 series CAS4 by OBD.

Preparation
A BMW smart key with frequency 315 Mhz
Autel MaxiIM IM608 Pro

Connect Autel IM608 Pro with OBD via APC101 cable
Important: voltage must be at 13V
Turn ignition ON but do not start the engine.

Procedure

Go to IM608 tablet to start:
IMMO >> Accept >> BMW >> Automatic selection >> Read >> OK >> Yes

Autel-Im608-Pro-Program-Bmw-2011-535i-Cas4-A-Key-By-Obd-1
Autel-Im608-Pro-Program-Bmw-2011-535i-Cas4-A-Key-By-Obd-2
Autel-Im608-Pro-Program-Bmw-2011-535i-Cas4-A-Key-By-Obd-3
Autel-Im608-Pro-Program-Bmw-2011-535i-Cas4-A-Key-By-Obd-4
Autel-Im608-Pro-Program-Bmw-2011-535i-Cas4-A-Key-By-Obd-5

To check immobilizer info, OBD position and key info, press “Vehicle immo information”.

Press “Immo status scan” to go on.

Press “Quick DTC clearing” if there were any DTCs.

Press “Add key” if there were not.

Autel-Im608-Pro-Program-Bmw-2011-535i-Cas4-A-Key-By-Obd-6
Autel-Im608-Pro-Program-Bmw-2011-535i-Cas4-A-Key-By-Obd-7
Autel-Im608-Pro-Program-Bmw-2011-535i-Cas4-A-Key-By-Obd-8

Note: Please make sure IM608 Pro is online with WIFI during processing and carefully read the notes on screen!

OK >> OK >> OK

Wait programming until 100%… do not touch any button of vehicle.

Restoring coding file…

Reading password…

Read password successful. Record it and press “OK”.

Autel-Im608-Pro-Program-Bmw-2011-535i-Cas4-A-Key-By-Obd-9
Autel-Im608-Pro-Program-Bmw-2011-535i-Cas4-A-Key-By-Obd-10
Autel-Im608-Pro-Program-Bmw-2011-535i-Cas4-A-Key-By-Obd-11
Autel-Im608-Pro-Program-Bmw-2011-535i-Cas4-A-Key-By-Obd-12

Select a free key position: Key 7, press “Add key”.

Put the new key close to start coil, press “OK”.

Autel-Im608-Pro-Program-Bmw-2011-535i-Cas4-A-Key-By-Obd-13
Autel-Im608-Pro-Program-Bmw-2011-535i-Cas4-A-Key-By-Obd-14
Autel-Im608-Pro-Program-Bmw-2011-535i-Cas4-A-Key-By-Obd-15

Key learning has 2 steps, please wait…
The 1st step of authenticating key information is in progress…
Write key successful!
Put the key close to start induction coil, press and hold the ignition for 10s.
After the learning is completed, the key can be normally used.
Press “OK”.
As you can see, the Key 7 turns to be used status with ID data now.

Let’s test the new key finally, it does work well.

Key programming has done!

Autel-Im608-Pro-Program-Bmw-2011-535i-Cas4-A-Key-By-Obd-16
Autel-Im608-Pro-Program-Bmw-2011-535i-Cas4-A-Key-By-Obd-17
Autel-Im608-Pro-Program-Bmw-2011-535i-Cas4-A-Key-By-Obd-18
Autel-Im608-Pro-Program-Bmw-2011-535i-Cas4-A-Key-By-Obd-19

Using Autel IM608 Pro Scan Tool to add a key for BMW 2011 535i CAS4 successfully!

If you want to learn more about Autel Scanner, please visit our website obd2tool.com

Labels:

Comments

Post a Comment

Popular posts from this blog

How to Solve VW Amarok Caddy 2018+ Remote Not Working After Programming

Here comes the general problem of VW Amarok Caddy etc. 2018+ UDS protocol vehicles: 2019 VW Caddy. I spent a few hours programming the Xhorse key using VVDI2 . Also tried TDB1000. Remote function could not be obtained. Every time the programming failed, the original remote stopped working until I scanned and cleared errors. I expected it to work when the transponder was added (Megamos AES). I can’t access remote learning with any of my tools, nor did vvdi2 let me program the remote. I was wondering if anyone could confirm remote learning with transponders or how to learn it if not. Solution: It is not possible for BH remote controls after 2018 at the latest. You will not get any communication with the central locking remote control customization. You need a dealer key 100% and then learn from ODIS. There is no after-market solution, VAG blocked the remote channel on UDS vehicles 2018+. Had the exact same issues with new caddies. So merchant key and Odis ATM since the c...
Post a Comment
Read more

How to Install Mercedes Benz DTS Monaco 8.16 Software

  This instruction show you the guide on how to install Mercedes Benz DTS Monaco Software . Preparations: Benz DTS Monaco Software Free Download After finish downoading and extract you will get below files Double click DTS-Setup to start installation Then just click default option to continue Click Finish Copy files in the repalce folder to DTS Monaco installation folder replace C:\Program Files(x86)\Softing\Diagnostic Tool Set 8\8.16\bin Then run “DTS Monacon” icon on desktop,it will show you the HWID and ask you to activate Please sent me your HWID to me(sales@obd2tool.com),we will sent you a activate file and license file When you get the xxx.reg file,doulbe click it to register it to your pc,click yes to add it the registy Run DTS Monaco and select “Administrate and manage DTS projects’ Select “System”–>”Add license” Load the License_0000000000000.bin file i sent you before Now your DTS Monaco have activated successfully! DTS Monaco 8.03.12 Softw...
Post a Comment
Read more

How to install TIS2000 TIS2Web GlobalTIS for TECH 2

This is Trollhattan’s contribution for those interested in playing with a Tech 2 Scan Tool , here’s a little info regarding the software requirements once you’ve got your hands on a Tech 2 handset. Firstly, I’m by no means an expert on this having only recently got this up and running myself, but I think that’s the tricky part. I’d welcome comments on where this post can be improved/altered etc. Most of the information is already out there on various boards/forums but it would be nice to try to bring it together for us with a purely Saab interest. For those who don’t know, the Tech 2 unit (handset) can be used to interrogate the various management modules on the car (ECU) to report status, fault codes and perform manual activation and monitoring in the event of fault occurrences/engine management light occurrences. This in itself is incredibly useful, but it is also possible to reprogram modules within the car to change various functions and add or replace faul...
Post a Comment
Read more