Car Diagnostic Tools From webstie obd2tool.com

Itemm will be shipped via DHL UPS TNT Fedex or EMS with tracking on. BMW ICOM Next  A Latest Generation Diagnostic Head For BMW, MINI, Rolls-Royce BMW-Model. Can Replace BMW ICOM A2, including all function of ICOM A2. BMW ICOM NEXT not support WIFI. ICOM NEXT can works together with ICOM Software we provided. ICOM NEXT can connect internet and Printer. Improved Functionality and Performance: 1. Gbit workshop LAN, backwards compatible 2. Preparation for Gbit LAN on vehicle OBD(cars do not yet supportthis and interface not yet defined,ICOM Next hardware adaptation will be necessary for future Gbit car interface,will cause adaptation costs) 3. Faster start-up times and high throughput 4. Through high-performance,low-power ARM SoC 5. Improved handling 6. More flexible OBD cable 7. Lighted button for logs etc ICOM NEXT A+B+C Diadnostic Head Overview? Functionally compatible to ICOM A2 Mechanical design similar ICOM A2 Backwards compatible to car adapt...

This blog list 3 kinds of  bmw diagnostic scanner ISTA errors and solutions you may need. ISTA NCS error IFH-0010+ solution ISTA error”MSVCP120.dll is missing”+ solution ISTA error “The vehicle could not be identified”+ solution Note: All error solutions here are suitable for  BMW ICOM A2 and BMW ICOM Next ! ISTA error IFH-0010: DATATRANSMISSION TO CONTROLUNIT DISTURBED ISTA error: A communication fault occurred during activation Incorrect state: ERROR ECU CONDITIONS NOT CORRECT OR REQUEST SEQUENCE ERROR Solution: Try setting COM port latency to 1 in Advanced Settings for the port. You should change it to 1 to have the least lag/disturbances between data transfer. BMW ISTA System error “MSVCP120.dll is missing” The program can’t start because MSVCP120.dll is missing from your computer. Solution: Reinstall VC++ Redistributables and try again. If you’re running x64, you will need both x86 and x64 bit versions installed. Feedback: I got rid o...

This is the instruction on how to change vehicle order (VO) with NCS Expert, on BMW vehicles except F series. VO modify tools: ICOM A2 NCS Expert (for BMW F series, you need ENET cable + E-sys) steps to modify VO: 1.In NCS Expert, load the Expertmode profile. 2.Press F1 or the VIN/ZCS/FA button. 3.Press F3 or the ZCS/FA f. ECU button. 4.In the Choose CHASSIS pop-up window, choose the E89 chassis and press the OK button. 5.In the Choose ECU pop-up window, choose the CAS ECU and press the OK button. 6.The model (CHASSIS), VIN number (FG), and VO (FA) should be displayed in NCS Expert. 7.Press F2 or the Enter FA button to modify the VO. 8.In the Choose CHASSIS pop-up window, choose the E89 chassis and press the OK button. 9.In the Enter VIN pop-up window, verify that the Vin listed is the correct VIN number for the vehicle. The last digit attached to the VIN number is a checksum. You should not have to change anything on this step. Just ve...

I have a 2014 M5 and flashed the car, the junction box and a bunch of other modules too, with ISTA/P 2.52.4 and an BMW ICOM clone A2 from www.obd2tool.com . It was the fourth or fifth car that I had flashed with this equipment. It seemed that ISTA/P crashed during flashing. ISTA/P is now not able to read the VO from VCM (also E-sys) and if you load the stored VO and read out the ECU with E-Sys (read VCM isn’t possible) you see 0 ECUs. It looks like that all ECUs are unavailable and in programming mode. He can open and close the car but nothing more. Connection via E-Sys is only possible by Gateway/Url (OBD Ethernet cable) or ICOM IP. ZGW is of course not available. What I did to fix it is, I used Esys to fix the BMW Diagnostic Tool . I need to use the Psdzdata that was on the module before it was flashed. Run these step like flashing a module Here are the basic steps: Go to Comfort Mode => TAL-Calculating – Read and Save FA – Activate FA – Read and Save SVT Actual...