Skip to main content

What is the default PC connection for an MDI

gm-mdi-5
1.What is the default PC connection for an MDI?
An GM MDI Scanner must be able to connect to your PC via USB. The USB interface is the only way to update/recover MDI software and configure other interfaces.
2.Can an MDI be configured for more than one interface?
An MDI may be configured for all three interfaces simultaneously, USB, Wired Ethernet and Wireless. However, a user can only connect to the MDI on one interface. Hovering the cursor over an MDI icon in the MDI Manager’s Explorer window will prompt a pop up to display the IP addresses for all available interfaces.
3.Can the MDI be configured to support Multiple Wireless Connections?
No – the current MDI firmware supports only a single wireless configuration.
4.In Service Programming, why doesn’t the ‘Device Explorer’ screen reappear for each programming event after I have selected an MDI?
Once an MDI is selected from the Device Explorer screen, it is used for the entire SPS session. To select a different MDI, close and then restart the SPS application.
5.What if MDI is not displayed in the MDI Manager Explorer window?
The MDI Manager software does not see the MDI.
?Verify the Auto Scanner Tool MDI is powered-on and has completed the POST.
?Connect the MDI to the PC using the USB connection, If the MDI does not appear in the explorer window then check the cable connections and verify the USB driver has been installed on the PC (look for device name ‘ETAS USB Remote NDIS Network Device’ under Network Connections).
?Verify that no other MDI is connected to the PC using the USB interface.
?If using a Wired Ethernet (LAN) connection check the Ethernet cable connections and verify the MDI and the PC are cabled into separate LAN connections on the same network.
?If using a Wireless connection check the following
oThe wireless card is installed and properly seated in the MDI
oConfirm the PC and the GM MDI WIFI are within ‘range’ of the Access Point or Router.
oWhile connected via USB check
?The MDI wireless signal strength
?The PC and MDI are configured to use the same wireless network

Comments

Popular posts from this blog

How to Solve VW Amarok Caddy 2018+ Remote Not Working After Programming

Here comes the general problem of VW Amarok Caddy etc. 2018+ UDS protocol vehicles: 2019 VW Caddy. I spent a few hours programming the Xhorse key using VVDI2 . Also tried TDB1000. Remote function could not be obtained. Every time the programming failed, the original remote stopped working until I scanned and cleared errors. I expected it to work when the transponder was added (Megamos AES). I can’t access remote learning with any of my tools, nor did vvdi2 let me program the remote. I was wondering if anyone could confirm remote learning with transponders or how to learn it if not. Solution: It is not possible for BH remote controls after 2018 at the latest. You will not get any communication with the central locking remote control customization. You need a dealer key 100% and then learn from ODIS. There is no after-market solution, VAG blocked the remote channel on UDS vehicles 2018+. Had the exact same issues with new caddies. So merchant key and Odis ATM since the c...

Lonsdor K518 Program Mini Cooper CAS3+ Remote Smart Key by OBD

Here’s the guide to program remote smart keys on a  Mini Cooper CAS3+ immobilizer  with Lonsdor K518  obd key programmer via OBD. Lonsdor K518ISE Key Programmer  host with vehicle via OBD socket Turn on device Select Immobilizer function on main menu Select BMW->Select from type->CAS2/CAS3 series->Program Key Will start to make dealer key Insert key into card slot and press on Start button once Lonsdor K518 ISE key programmer will display CAS part number and type. Reading RAM… wait for 1 minute Remove key from ignition switch. For smart eym take it outside car. Click OK to continue Safety checking Reading key inforamtion Select a key position to program If car key has been programmed but failed, please unlock the key and restore CAS data first Press OK to continue Select Remote Key Pull Lonsdor K518 key on  OBD2 slot to the right and insert the key to program (to identify if the key is legal and to pre-p...

The 11 Special Reset Functions Every OBD Scanner Must Have

Buying an OBD2 Scanner might be a confusing process if you have no idea which scanner to choose. The OBD scanner in your automobile should be able to execute the following 11 critical functions. To summarize, it is better to buy an OBD scanner if it offers these 11 unique features. Oil Reset Service This function can be performed in the following cases: 1.  If the service lamp is on, you must provide service for the car. After service, you need to reset the driving mileage or driving time so that the service lamp turns off and the system enables the new service cycle. 2.  After changing engine oil or electric appliances that monitor oil life, you need to reset the service lamp. Steering Angle Calibration 1.  To reset the steering angle, first find the relative zero point position for the car to drive in a straight line. Taking this position as reference, the ECU can calculate the accurate angle for left and right steering. 2.  After replacing the s...