Skip to main content

How to Program BMW F01 CAS4 2010 Remote Key with Lonsdor K518ISE Auto Key Programmer?

Vehicle Model: BMW F-series F01 year 2010

Remote type: PCF7953, 868MHz

Immo type: CAS4 1L16Y

Device to program: key renew tool, Lonsdor K518ise and VVDI Prog
1

Procedure:
Step 1: Renew key (if have new key go to Step 2)
Step 2: Read dump
Step 3: Add a new key

Step 1: Renew used key
by Tango or MK3 programmers
2
3
4

Step 2: Read CAS4 data
Remove CAS4 module
5
Follow vvdi prog wiring diagram to connect CAS and programmer
6
7
Read CAS4 1L16Y data and save dump.
8

Step 3: Program key with Lonsdor K518ISE
In K518ISE, select Immobilizer->BMW->Select from type->CAS4/CAS4+ ->Make ignition key
9
Copy and paste the CAS4 EEPROM data to Lonsdor “customfile” folder
10
Upload EEPROM dump
11
Select a key position to add key
12
Insert new key to be generated into K518 card slot
13
Follow K518ise instructions to generate ignition key
1.Take all other keys out of car except the new key

2.Close newly generated key to car induction coil

3.Press Start button and wait for 15 sec (remove key when dash turns on)

4.Check all function of the new key
14
Test the new key
Remote detect and can start engine.
15
Done.
Labels:

Comments

Post a Comment

Popular posts from this blog

VAG OBD Helper Software

VAG OBD helper 4th Immo Data Calculator free download source and installation guide. VAG OBD helper free download source: https://mega.nz/#!gZJzTKTC!BTVJqa-SmWgrwbd-n0vV8r2glx23d3l2OpN3ZRu1gXU Download the above link on the desktop. Decompress it. Install the driver firstly, then use the USB port to connect the device. Open the software, you will see the serial number read by the cable, the language is Chinese and English. There are some pdf files in Chinese on how to use VAG OBD helper to read out the 4th IMMO data and then use the key programmer to program key. VAG OBD helper Token: Each time the user read out the IMMO data, it will cost one token. Usually the VAG OBD helper comes with one free token FROM www.obd2tool.com , after it use up, just send the supplier serial number to charge more.
Post a Comment
Read more

Solved BMW ISTA error IFH-0010, Vehicle could not be identified

This blog list 3 kinds of  bmw diagnostic scanner ISTA errors and solutions you may need. ISTA NCS error IFH-0010+ solution ISTA error”MSVCP120.dll is missing”+ solution ISTA error “The vehicle could not be identified”+ solution Note: All error solutions here are suitable for  BMW ICOM A2 and BMW ICOM Next ! ISTA error IFH-0010: DATATRANSMISSION TO CONTROLUNIT DISTURBED ISTA error: A communication fault occurred during activation Incorrect state: ERROR ECU CONDITIONS NOT CORRECT OR REQUEST SEQUENCE ERROR Solution: Try setting COM port latency to 1 in Advanced Settings for the port. You should change it to 1 to have the least lag/disturbances between data transfer. BMW ISTA System error “MSVCP120.dll is missing” The program can’t start because MSVCP120.dll is missing from your computer. Solution: Reinstall VC++ Redistributables and try again. If you’re running x64, you will need both x86 and x64 bit versions installed. Feedback: I got rid o...
Post a Comment
Read more

How to Install Mercedes Benz DTS Monaco 8.16 Software

  This instruction show you the guide on how to install Mercedes Benz DTS Monaco Software . Preparations: Benz DTS Monaco Software Free Download After finish downoading and extract you will get below files Double click DTS-Setup to start installation Then just click default option to continue Click Finish Copy files in the repalce folder to DTS Monaco installation folder replace C:\Program Files(x86)\Softing\Diagnostic Tool Set 8\8.16\bin Then run “DTS Monacon” icon on desktop,it will show you the HWID and ask you to activate Please sent me your HWID to me(sales@obd2tool.com),we will sent you a activate file and license file When you get the xxx.reg file,doulbe click it to register it to your pc,click yes to add it the registy Run DTS Monaco and select “Administrate and manage DTS projects’ Select “System”–>”Add license” Load the License_0000000000000.bin file i sent you before Now your DTS Monaco have activated successfully! DTS Monaco 8.03.12 Softw...
Post a Comment
Read more