Skip to main content

OBD2 protocol: Which is supported by my vehicle?

 

OBD2 is used in the automotive industry to refer to the onboard diagnostics system. It has more advanced features than its predecessor obd1. An OBD-II compliant vehicle can use any of the five communication protocols: J1850 PWM, J1850 VPW, ISO9141-2, ISO14230 (also called KWP2000), ISO15765-4/SAE J2480.

OBD2-protocol-Which-is-supported-by-my-vehicle-1

Types of OBD2 protocols
Below are  OBD2 protocols by vehicle make and model:
SAE J1850 PWM,SAE J1850 VPW,ISO 9141-2,ISO 14230 KWP2000,ISO 15765-4 CAN (SAE J2480)
1.SAE  J1850  VPW: This OBD2 protocol is used by Ford.

OBD2-protocol-Which-is-supported-by-my-vehicle-2

2. SAE J1850 PWM: Common Motors utilize this protocol.

OBD2-protocol-Which-is-supported-by-my-vehicle-3

3. ISO 9141-2: You will find this protocol on Asian, Chrysler, and European cars.

OBD2-protocol-Which-is-supported-by-my-vehicle-4

4.ISO 14230 KWP2000: This protocol is found in Asian vehicles.
5. You will find this protocol in many vehicles made after 2008.

OBD2-protocol-Which-is-supported-by-my-vehicle-5

For most scanners, you just need an OBD2-compliant vehicle. You can normally use any scanner with any protocol. However, there are times when you want to be more specific. Not every OBD2 protocol connects with the scanner the same way. Unfortunately, the only way to know what protocol you have is to look at the pin datasheet of your vehicle’s connector.

OBD2-protocol-Which-is-supported-by-my-vehicle-6

Top 8 Pins
1.Reserved for OEM COMM
2.J1850 Bus+ (positive)
3.OEM Reserved
4.Framework/car chassis ground
5.Sensor signal ground
6.OEM COMM / CAN High
7.K-line
8.OEM Reserved
Bottom 8 Pins
9.OEM COMM
10.J1850 Bus- (negative)
11.OEM Reserved
12.OEM Reserved
13.OEM Reserved
14.OEM Reserved / CAN Low
15.L-line
16.Power out (12 volts)
17.The following table explains how to determine the protocol:

Comments

Post a Comment

Popular posts from this blog

Solved BMW ISTA error IFH-0010, Vehicle could not be identified

This blog list 3 kinds of  bmw diagnostic scanner ISTA errors and solutions you may need. ISTA NCS error IFH-0010+ solution ISTA error”MSVCP120.dll is missing”+ solution ISTA error “The vehicle could not be identified”+ solution Note: All error solutions here are suitable for  BMW ICOM A2 and BMW ICOM Next ! ISTA error IFH-0010: DATATRANSMISSION TO CONTROLUNIT DISTURBED ISTA error: A communication fault occurred during activation Incorrect state: ERROR ECU CONDITIONS NOT CORRECT OR REQUEST SEQUENCE ERROR Solution: Try setting COM port latency to 1 in Advanced Settings for the port. You should change it to 1 to have the least lag/disturbances between data transfer. BMW ISTA System error “MSVCP120.dll is missing” The program can’t start because MSVCP120.dll is missing from your computer. Solution: Reinstall VC++ Redistributables and try again. If you’re running x64, you will need both x86 and x64 bit versions installed. Feedback: I got rid o...
Post a Comment
Read more

How to Solve VW Amarok Caddy 2018+ Remote Not Working After Programming

Here comes the general problem of VW Amarok Caddy etc. 2018+ UDS protocol vehicles: 2019 VW Caddy. I spent a few hours programming the Xhorse key using VVDI2 . Also tried TDB1000. Remote function could not be obtained. Every time the programming failed, the original remote stopped working until I scanned and cleared errors. I expected it to work when the transponder was added (Megamos AES). I can’t access remote learning with any of my tools, nor did vvdi2 let me program the remote. I was wondering if anyone could confirm remote learning with transponders or how to learn it if not. Solution: It is not possible for BH remote controls after 2018 at the latest. You will not get any communication with the central locking remote control customization. You need a dealer key 100% and then learn from ODIS. There is no after-market solution, VAG blocked the remote channel on UDS vehicles 2018+. Had the exact same issues with new caddies. So merchant key and Odis ATM since the c...
Post a Comment
Read more

VAG OBD Helper Software

VAG OBD helper 4th Immo Data Calculator free download source and installation guide. VAG OBD helper free download source: https://mega.nz/#!gZJzTKTC!BTVJqa-SmWgrwbd-n0vV8r2glx23d3l2OpN3ZRu1gXU Download the above link on the desktop. Decompress it. Install the driver firstly, then use the USB port to connect the device. Open the software, you will see the serial number read by the cable, the language is Chinese and English. There are some pdf files in Chinese on how to use VAG OBD helper to read out the 4th IMMO data and then use the key programmer to program key. VAG OBD helper Token: Each time the user read out the IMMO data, it will cost one token. Usually the VAG OBD helper comes with one free token FROM www.obd2tool.com , after it use up, just send the supplier serial number to charge more.
Post a Comment
Read more