Skip to main content

How to Modify Tactrix Openport 2.0 Clone to Enable Network Connection

In the previous post, we discussed how to choose a high-quality Tactrix Openport 2.0 Clone. Today we share another guide for correct resistors in order to make it work with the network connection.

The HQ openport 2.0 clone does not allow network connection without modification. Otherwise, it will brick the device.

How to Modify Tactrix Openport 2.0 Clone to Enable Network Connection?

Disclaimer: the modification guide was made by a Russian technician from drive2. You are at your risk. We are not holding the responsibility for your damage.

Here are the tips to modify the Openport 2.0 HQ clone with black board to avoid damage when connecting with the network.

6 resistors were soldered in each ( check table of replacements ) to bring them into line with the original, one additional resistor and two electrolytic capacitors were soldered to the LM voltage regulator (aka LD-shka, aka AMS1117). And both work and are not afraid of the Internet.

table of ratings and replacements


orig the clone Replacement of herbs. China Black board Replacement
R1 51k 01D 513 103 513
R2 01C 01D 103 103
R3 01D 01D
103 104
R4 2,2m 2,2m
225 (R9)
R5 220k 220k
224
R6 220k 220k
224
R7 2,7k 2,7k
272
R8 74C 74С
74С
R9 01C 01D 103 103
R10 74C 74C
74C
R11 01C 01D 103 103
R12 1,5k 13B (1,33k) 152 152
R13 22k 22k
223
R14 01C 01D 103 103
R15 01C 01D 103 103
R16 240 240
241
R17 01C 01D 103 103
R18 2,2k 2,2k
222
R19 1,5k 01B (1k) 152 01B (1k) 152
R20 4,7k 4,7k
472
R21 22 22
220
R22 22 22
220
R23 1k 1k
102
R24 22k 22k
223
R25 2,2k 2,2k
222
R26 01C 01D 103 103
R27 1k 1k
102
R28 22k 22k
223
R29 2,2k 2,2k
222
R30 01C 01D 103 103
R31 4,7k 2,7k 472 272 472
R32 470 470
471
R33 22k 22k
223
R34 1.8k 1.8k
182
R35 22k 22k
223
R36 01B 01B
01B
R37 4,7k 2,7k 472 272 472
R38 01C 01D 103 103
R39 2,7k 2,7k
272
R40 2,7k 2,7k
272
R41 01D 2,7k 104 272 104
R42 01C 01D 103 103
R43 2,7k 2,7k
272
R44 2,7k 2,7k
272
R45 01C 01D 103 103
R46 2,2k 2,2k
222
R47 01C 01D 103 103
R48 2,2k 2,2k
222
R49 74C 74C
74C
R50 01C 01D 103 103
R51 74C 74C
74C
R52 01C 01D 103 103






How-to-Modify-Tactrix-Openport-2.0-Clone-to-Enable-Network-Connection-1
How-to-Modify-Tactrix-Openport-2.0-Clone-to-Enable-Network-Connection-2

In parallel to C8, 10 uF ceramics are soldered.

How-to-Modify-Tactrix-Openport-2.0-Clone-to-Enable-Network-Connection-3

LM-ke for output 1 and 3 electrolyte 100×25.

How-to-Modify-Tactrix-Openport-2.0-Clone-to-Enable-Network-Connection-4

But in pulled up to the plus through a 10k resistor from C12.

How-to-Modify-Tactrix-Openport-2.0-Clone-to-Enable-Network-Connection-5

Butpin 53 output – 10k pull-up connection points.

In sum in order to replacing the resistors on the Tactrix Openport 2.0 Clone, you can do the following:
1). To capacitor C8, soldered a ceramic capacitor of 10 uF
2). On pins 1 and 3 of LD33, added an electrolytic capacitor of 100 uF, 25 V.
3). From plus C12 to pin 53 (P2[10] /EINT0) LPC2364, added a 10 kΩ resistor. This modification prevents the bootloader located in the LPC2364 from starting when the RESET command is given to the microcontroller.

Everything you do is at your own risk, we are not responsible for dead adapters.

More detail component pictures

How-to-Modify-Tactrix-Openport-2.0-Clone-to-Enable-Network-Connection-6
How-to-Modify-Tactrix-Openport-2.0-Clone-to-Enable-Network-Connection-7
How-to-Modify-Tactrix-Openport-2.0-Clone-to-Enable-Network-Connection-8
How-to-Modify-Tactrix-Openport-2.0-Clone-to-Enable-Network-Connection-9
How-to-Modify-Tactrix-Openport-2.0-Clone-to-Enable-Network-Connection-10
How-to-Modify-Tactrix-Openport-2.0-Clone-to-Enable-Network-Connection-12
How-to-Modify-Tactrix-Openport-2.0-Clone-to-Enable-Network-Connection-13
How-to-Modify-Tactrix-Openport-2.0-Clone-to-Enable-Network-Connection-14
How-to-Modify-Tactrix-Openport-2.0-Clone-to-Enable-Network-Connection-15


Comments

Popular posts from this blog

How to Solve VW Amarok Caddy 2018+ Remote Not Working After Programming

Here comes the general problem of VW Amarok Caddy etc. 2018+ UDS protocol vehicles: 2019 VW Caddy. I spent a few hours programming the Xhorse key using VVDI2 . Also tried TDB1000. Remote function could not be obtained. Every time the programming failed, the original remote stopped working until I scanned and cleared errors. I expected it to work when the transponder was added (Megamos AES). I can’t access remote learning with any of my tools, nor did vvdi2 let me program the remote. I was wondering if anyone could confirm remote learning with transponders or how to learn it if not. Solution: It is not possible for BH remote controls after 2018 at the latest. You will not get any communication with the central locking remote control customization. You need a dealer key 100% and then learn from ODIS. There is no after-market solution, VAG blocked the remote channel on UDS vehicles 2018+. Had the exact same issues with new caddies. So merchant key and Odis ATM since the c...

Lonsdor K518 Program Mini Cooper CAS3+ Remote Smart Key by OBD

Here’s the guide to program remote smart keys on a  Mini Cooper CAS3+ immobilizer  with Lonsdor K518  obd key programmer via OBD. Lonsdor K518ISE Key Programmer  host with vehicle via OBD socket Turn on device Select Immobilizer function on main menu Select BMW->Select from type->CAS2/CAS3 series->Program Key Will start to make dealer key Insert key into card slot and press on Start button once Lonsdor K518 ISE key programmer will display CAS part number and type. Reading RAM… wait for 1 minute Remove key from ignition switch. For smart eym take it outside car. Click OK to continue Safety checking Reading key inforamtion Select a key position to program If car key has been programmed but failed, please unlock the key and restore CAS data first Press OK to continue Select Remote Key Pull Lonsdor K518 key on  OBD2 slot to the right and insert the key to program (to identify if the key is legal and to pre-p...

The 11 Special Reset Functions Every OBD Scanner Must Have

Buying an OBD2 Scanner might be a confusing process if you have no idea which scanner to choose. The OBD scanner in your automobile should be able to execute the following 11 critical functions. To summarize, it is better to buy an OBD scanner if it offers these 11 unique features. Oil Reset Service This function can be performed in the following cases: 1.  If the service lamp is on, you must provide service for the car. After service, you need to reset the driving mileage or driving time so that the service lamp turns off and the system enables the new service cycle. 2.  After changing engine oil or electric appliances that monitor oil life, you need to reset the service lamp. Steering Angle Calibration 1.  To reset the steering angle, first find the relative zero point position for the car to drive in a straight line. Taking this position as reference, the ECU can calculate the accurate angle for left and right steering. 2.  After replacing the s...