Skip to main content

Opel Antara all keys lost Lonsdor K518ise can do it


Opel-Antara-all-keys-lost-Lonsdor-K518ise-1
Lonsdor K518ISE and Opel Antara all keys lost: possible?
Did you successfully make all keys lost (AKL) to Opel Antara with Lonsdor?
Yes, I made it some time ago
Anyone helps me confirm Antara is listed in Lonsdor?
Antara is supported by the Lonsdor k518ise first release:
OPEL\Remote system\Antara: Program remote, Delete remote
OPEL\IMMO\Select from vehicle\Antara: All keys lost
Does any one made AKL to Antara with Lonsdor K518ise? Car can be started for few times with each key and then turns all off …. chip ID is the same as for both keys
Opel-Antara-all-keys-lost-Lonsdor-K518ise-2
Opel-Antara-all-keys-lost-Lonsdor-K518ise-3
Opel-Antara-all-keys-lost-Lonsdor-K518ise-4
You need to program the keys in one single procedure, it happened to me programming a spare, ended up with two not working. Had to reprogram as AKL. Remote procedure separate.
Good to know: If you don’t have a good success on your Opel or cannot find out the corresponding model in the vehicle menu, had better try “select from type” and maybe you’ll have luck.
Opel-Antara-all-keys-lost-Lonsdor-K518ise-5
Example: A big success with “select from type”
Car: Opel Astra 2013
Immobilizer: select from type, type 1
Read pin codes
Program new keys
Upload images…
Opel-Antara-all-keys-lost-Lonsdor-K518ise-6 Opel-Antara-all-keys-lost-Lonsdor-K518ise-7 Opel-Antara-all-keys-lost-Lonsdor-K518ise-8 Opel-Antara-all-keys-lost-Lonsdor-K518ise-9 Opel-Antara-all-keys-lost-Lonsdor-K518ise-10 Opel-Antara-all-keys-lost-Lonsdor-K518ise-11
Success!

Labels

Labels:

Comments

Post a Comment

Popular posts from this blog

VAG OBD Helper Software

VAG OBD helper 4th Immo Data Calculator free download source and installation guide. VAG OBD helper free download source: https://mega.nz/#!gZJzTKTC!BTVJqa-SmWgrwbd-n0vV8r2glx23d3l2OpN3ZRu1gXU Download the above link on the desktop. Decompress it. Install the driver firstly, then use the USB port to connect the device. Open the software, you will see the serial number read by the cable, the language is Chinese and English. There are some pdf files in Chinese on how to use VAG OBD helper to read out the 4th IMMO data and then use the key programmer to program key. VAG OBD helper Token: Each time the user read out the IMMO data, it will cost one token. Usually the VAG OBD helper comes with one free token FROM www.obd2tool.com , after it use up, just send the supplier serial number to charge more.
Post a Comment
Read more

Solved BMW ISTA error IFH-0010, Vehicle could not be identified

This blog list 3 kinds of  bmw diagnostic scanner ISTA errors and solutions you may need. ISTA NCS error IFH-0010+ solution ISTA error”MSVCP120.dll is missing”+ solution ISTA error “The vehicle could not be identified”+ solution Note: All error solutions here are suitable for  BMW ICOM A2 and BMW ICOM Next ! ISTA error IFH-0010: DATATRANSMISSION TO CONTROLUNIT DISTURBED ISTA error: A communication fault occurred during activation Incorrect state: ERROR ECU CONDITIONS NOT CORRECT OR REQUEST SEQUENCE ERROR Solution: Try setting COM port latency to 1 in Advanced Settings for the port. You should change it to 1 to have the least lag/disturbances between data transfer. BMW ISTA System error “MSVCP120.dll is missing” The program can’t start because MSVCP120.dll is missing from your computer. Solution: Reinstall VC++ Redistributables and try again. If you’re running x64, you will need both x86 and x64 bit versions installed. Feedback: I got rid o...
Post a Comment
Read more

How to Install Mercedes Benz DTS Monaco 8.16 Software

  This instruction show you the guide on how to install Mercedes Benz DTS Monaco Software . Preparations: Benz DTS Monaco Software Free Download After finish downoading and extract you will get below files Double click DTS-Setup to start installation Then just click default option to continue Click Finish Copy files in the repalce folder to DTS Monaco installation folder replace C:\Program Files(x86)\Softing\Diagnostic Tool Set 8\8.16\bin Then run “DTS Monacon” icon on desktop,it will show you the HWID and ask you to activate Please sent me your HWID to me(sales@obd2tool.com),we will sent you a activate file and license file When you get the xxx.reg file,doulbe click it to register it to your pc,click yes to add it the registy Run DTS Monaco and select “Administrate and manage DTS projects’ Select “System”–>”Add license” Load the License_0000000000000.bin file i sent you before Now your DTS Monaco have activated successfully! DTS Monaco 8.03.12 Softw...
Post a Comment
Read more