Skip to main content

Original DSPIII+ DSP3+Odometer Correction Tool Full Package Include All Software And Hardware

Introduction
DSP III+ is the most complete programming device for digital odometers, airbag modules, car radios, car immobilizers.
It is a high-quality embeded system, which offers a maximum of flexibility and working comfort.
Original-DSPIII+-DSP3+Odometer-Correction-Tool-Full-Package-1
Original-DSPIII+-DSP3+Odometer-Correction-Tool-Full-Package-2
Technical reference
Power by ARM 10 TDI and CORTEX ARM cores, speeds up to 600MHZ, 800*480 TFT LCD and touch screen(7.0″.16:9).
Convenient keyset. USB host and USB device. SD card interface. 128MB NandFlash, 128MB SDRAM.
Self-check function integrated in system.
Enhanced OBD functions, including CAN-BUS / J1850 / CCD-BUS / ISO9141 / SPI protocols.
Intuitive operability by full menu and picture guidance. All data can be edited, stored and loaded.
Color connection picture is on the screen whenever you need.
The stored data can be transferred to a PC by USB port or SD card, and also can be transfer to wherever you want  directly by internet.
Update directly from internet.
Original-DSPIII+-DSP3+Odometer-Correction-Tool-Full-Package-3
Odometer full package (include all software and hardware)
Odometer full package:
Machine, OBD cables, EEPROM, MOTOROLA, NEC, TMS, HC711, HC908, HCS12 in-circuit,
HC705, EWS, NDM457, ST624, TMS374, CMM, JC adapter, BENZ-38 connector, BWM-20 connector,
BMW CAS cables and BENZ cluster cable, SD card, clips, touch-holders, USB cable, Power cables, with full soft.
Software:
OBD functions are all active.
Original-DSPIII+-DSP3+Odometer-Correction-Tool-Full-Package-4
Original-DSPIII+-DSP3+Odometer-Correction-Tool-Full-Package-5
ODOMETER SOFTWARE
Original-DSPIII+-DSP3+Odometer-Correction-Tool-Full-Package-6
IMMOBILIZER SOFTWARE
Original-DSPIII+-DSP3+Odometer-Correction-Tool-Full-Package-7
HARDWARE (ONE YEAR WARRANTY)
Original-DSPIII+-DSP3+Odometer-Correction-Tool-Full-Package-8
DSP III Odometer Correction Tool Full Package content:
– PDA main unit, with full software authorization
– Full set of all available adapters: EEPROM, Motorol*a, NEC, TMS 374, HC711, HC908, 9(S)12 in-circuit, HC705, EWS, NDM457, ST624, TMS 370, CMM, OBD, JC, AVR/PIC, D80/160, BCM2, C-04.
– All connectors and clips: OBD cables MERCEDES-38 connector, BWM-20 connector, BMW CAS cables, Mercedes cluster cable,
– SD card,
– All clips,
– All touch-holders,
– USB cable
Power cable
Original-DSPIII+-DSP3+Odometer-Correction-Tool-Full-Package-9


Labels:

Comments

Post a Comment

Popular posts from this blog

Solved BMW ISTA error IFH-0010, Vehicle could not be identified

This blog list 3 kinds of  bmw diagnostic scanner ISTA errors and solutions you may need. ISTA NCS error IFH-0010+ solution ISTA error”MSVCP120.dll is missing”+ solution ISTA error “The vehicle could not be identified”+ solution Note: All error solutions here are suitable for  BMW ICOM A2 and BMW ICOM Next ! ISTA error IFH-0010: DATATRANSMISSION TO CONTROLUNIT DISTURBED ISTA error: A communication fault occurred during activation Incorrect state: ERROR ECU CONDITIONS NOT CORRECT OR REQUEST SEQUENCE ERROR Solution: Try setting COM port latency to 1 in Advanced Settings for the port. You should change it to 1 to have the least lag/disturbances between data transfer. BMW ISTA System error “MSVCP120.dll is missing” The program can’t start because MSVCP120.dll is missing from your computer. Solution: Reinstall VC++ Redistributables and try again. If you’re running x64, you will need both x86 and x64 bit versions installed. Feedback: I got rid o...
Post a Comment
Read more

How to Solve VW Amarok Caddy 2018+ Remote Not Working After Programming

Here comes the general problem of VW Amarok Caddy etc. 2018+ UDS protocol vehicles: 2019 VW Caddy. I spent a few hours programming the Xhorse key using VVDI2 . Also tried TDB1000. Remote function could not be obtained. Every time the programming failed, the original remote stopped working until I scanned and cleared errors. I expected it to work when the transponder was added (Megamos AES). I can’t access remote learning with any of my tools, nor did vvdi2 let me program the remote. I was wondering if anyone could confirm remote learning with transponders or how to learn it if not. Solution: It is not possible for BH remote controls after 2018 at the latest. You will not get any communication with the central locking remote control customization. You need a dealer key 100% and then learn from ODIS. There is no after-market solution, VAG blocked the remote channel on UDS vehicles 2018+. Had the exact same issues with new caddies. So merchant key and Odis ATM since the c...
Post a Comment
Read more

VAG OBD Helper Software

VAG OBD helper 4th Immo Data Calculator free download source and installation guide. VAG OBD helper free download source: https://mega.nz/#!gZJzTKTC!BTVJqa-SmWgrwbd-n0vV8r2glx23d3l2OpN3ZRu1gXU Download the above link on the desktop. Decompress it. Install the driver firstly, then use the USB port to connect the device. Open the software, you will see the serial number read by the cable, the language is Chinese and English. There are some pdf files in Chinese on how to use VAG OBD helper to read out the 4th IMMO data and then use the key programmer to program key. VAG OBD helper Token: Each time the user read out the IMMO data, it will cost one token. Usually the VAG OBD helper comes with one free token FROM www.obd2tool.com , after it use up, just send the supplier serial number to charge more.
Post a Comment
Read more