wiTECH DRB III Car list For Chrysler Jeep Dodge diagnostic & program

Here is a list of wiTECH and DRB III functions to help you understand the programs used to diagnose and program Chrysler, Jeep, Dodge, Ram, SRT, Fiat, etc.

So, here comes two questions:

Question 1: Where to have DRB III emulator? I want it to communicate with 2006 Chrysler town and country

The answer is to have wiTECH VCI Pod V13.03.38, which comes with DRB III emulator and can work stably offline.

Question 2: Which hardware is compatible with clone wiTech software?

wiTech software is confirmed no issues with the Witech Micropod2. It can perform Chrysler Diagnostics and Programming.

You could use the clone for online diagnosis or new Chrysler cars.

If you have an account, you also are able to do online programming.

But the DRB III emulator is not always contained in its CD: Someone feedback he tried 2 Micropods, one did have no DRBIII functionality at all and the second did have DRBIII functionality, but only for the engine and transmission module (CAN bus) and no other modules (K Line).

Comments

Solved BMW ISTA error IFH-0010, Vehicle could not be identified

This blog list 3 kinds of bmw diagnostic scanner ISTA errors and solutions you may need. ISTA NCS error IFH-0010+ solution ISTA error”MSVCP120.dll is missing”+ solution ISTA error “The vehicle could not be identified”+ solution Note: All error solutions here are suitable for BMW ICOM A2 and BMW ICOM Next ! ISTA error IFH-0010: DATATRANSMISSION TO CONTROLUNIT DISTURBED ISTA error: A communication fault occurred during activation Incorrect state: ERROR ECU CONDITIONS NOT CORRECT OR REQUEST SEQUENCE ERROR Solution: Try setting COM port latency to 1 in Advanced Settings for the port. You should change it to 1 to have the least lag/disturbances between data transfer. BMW ISTA System error “MSVCP120.dll is missing” The program can’t start because MSVCP120.dll is missing from your computer. Solution: Reinstall VC++ Redistributables and try again. If you’re running x64, you will need both x86 and x64 bit versions installed. Feedback: I got rid o...

How to Solve VW Amarok Caddy 2018+ Remote Not Working After Programming

Here comes the general problem of VW Amarok Caddy etc. 2018+ UDS protocol vehicles: 2019 VW Caddy. I spent a few hours programming the Xhorse key using VVDI2 . Also tried TDB1000. Remote function could not be obtained. Every time the programming failed, the original remote stopped working until I scanned and cleared errors. I expected it to work when the transponder was added (Megamos AES). I can’t access remote learning with any of my tools, nor did vvdi2 let me program the remote. I was wondering if anyone could confirm remote learning with transponders or how to learn it if not. Solution: It is not possible for BH remote controls after 2018 at the latest. You will not get any communication with the central locking remote control customization. You need a dealer key 100% and then learn from ODIS. There is no after-market solution, VAG blocked the remote channel on UDS vehicles 2018+. Had the exact same issues with new caddies. So merchant key and Odis ATM since the c...

VAG OBD Helper Software

VAG OBD helper 4th Immo Data Calculator free download source and installation guide. VAG OBD helper free download source: https://mega.nz/#!gZJzTKTC!BTVJqa-SmWgrwbd-n0vV8r2glx23d3l2OpN3ZRu1gXU Download the above link on the desktop. Decompress it. Install the driver firstly, then use the USB port to connect the device. Open the software, you will see the serial number read by the cable, the language is Chinese and English. There are some pdf files in Chinese on how to use VAG OBD helper to read out the 4th IMMO data and then use the key programmer to program key. VAG OBD helper Token: Each time the user read out the IMMO data, it will cost one token. Usually the VAG OBD helper comes with one free token FROM www.obd2tool.com , after it use up, just send the supplier serial number to charge more.

Car Diagnostic Tools From webstie obd2tool.com

Search This Blog