2012 Ford Mondeo Steering Angle Sensor Calibration by X-431 PRO

X-431 PRO Test: 2012 Ford Mondeo Steering Angle Sensor Calibration Instructions

Tested Model: Ford Mondeo, 2012, VIN=WFOGXXGBBGCB*****

NOTES:

1. This function is used to configure the steering angle sensor and calibrate the steering wheel position. Perform this function when corresponding sensors are replaced or the steering wheel position is not accurate.

2. Keep the vehicle on a flat surface, and the steering wheel is set at straight ahead position.

Operation Procedure:

1. Select Ford version above V45.20.

2. Select automatic search.

3. Select Fuel Type=Gasoline.

4. Select “System Selection”

5. Select ABS (Anti-lock Brake System)/ESP (Electronic Stability Program) exhaust.

6. Check vehicle status and ensure that the vehicle is in required status: Vehicle on a flat surface, and the steering wheel is set at straight ahead position.

7. Select Special Function

8. Place the key to ON position in order to turn the steering wheel. Because of the great force of friction between tires and the ground, in order to turn the steering wheel more easily, it is advised to start the engine at this moment

9. Turn the steering wheel to the left and right respectively about 10 degree, then back to the straight ahead position.

10. After clicking OK, it counts down from 4 seconds configuring the module.

11. It prompts the procedure succeeded once the ECU configuration completed.

12. After this procedure succeeded, some vehicles may produce fault code due to this function execution, thus it is required to do self-test and clear the DTC, but most of the vehicles will not set fault codes.

13. After confirmation, it prompts to turn the ignition key to OFF to end the test.

Comments

How to Solve VW Amarok Caddy 2018+ Remote Not Working After Programming

Here comes the general problem of VW Amarok Caddy etc. 2018+ UDS protocol vehicles: 2019 VW Caddy. I spent a few hours programming the Xhorse key using VVDI2 . Also tried TDB1000. Remote function could not be obtained. Every time the programming failed, the original remote stopped working until I scanned and cleared errors. I expected it to work when the transponder was added (Megamos AES). I can’t access remote learning with any of my tools, nor did vvdi2 let me program the remote. I was wondering if anyone could confirm remote learning with transponders or how to learn it if not. Solution: It is not possible for BH remote controls after 2018 at the latest. You will not get any communication with the central locking remote control customization. You need a dealer key 100% and then learn from ODIS. There is no after-market solution, VAG blocked the remote channel on UDS vehicles 2018+. Had the exact same issues with new caddies. So merchant key and Odis ATM since the c...

John Deere Service Advisor 4.2 CF – Construction & Forestry incl. Hitachi + History DVD 2016

John Deere Service Advisor 4.2 CF – Construction & Forestry incl. Hitachi 2/2016 contains detailed information on all the procedures for repair and maintenance, a lot of illustrations, wiring diagrams, electrical and hydraulic circuits for construction and forestry equipment John Deere. Service Advisor contains information about setting up data, troubleshooting procedures, symptoms of malfunctions, the order of disassembly and assembly, adjustment data, torque. Electronic program is designed to handle all maintenance issues, eliminate breakdowns and malfunctions. Installation of this software is very easy and doesn’t require additional knowledge. The program allows you to quickly and easily find information and solve problems with machinery John Deere. This service advisor is designed to work with Windows XP, 7, 8. This software works under Windows 10 but wasn’t tested with EDL adapter and drivers. This version of Service Advisor has built-in hot...

How to Install Mercedes Benz DTS Monaco 8.16 Software

This instruction show you the guide on how to install Mercedes Benz DTS Monaco Software . Preparations: Benz DTS Monaco Software Free Download After finish downoading and extract you will get below files Double click DTS-Setup to start installation Then just click default option to continue Click Finish Copy files in the repalce folder to DTS Monaco installation folder replace C:\Program Files(x86)\Softing\Diagnostic Tool Set 8\8.16\bin Then run “DTS Monacon” icon on desktop,it will show you the HWID and ask you to activate Please sent me your HWID to me(sales@obd2tool.com),we will sent you a activate file and license file When you get the xxx.reg file,doulbe click it to register it to your pc,click yes to add it the registy Run DTS Monaco and select “Administrate and manage DTS projects’ Select “System”–>”Add license” Load the License_0000000000000.bin file i sent you before Now your DTS Monaco have activated successfully! DTS Monaco 8.03.12 Softw...

Car Diagnostic Tools From webstie obd2tool.com

Search This Blog