Skip to main content

Benz S350 221Chassis Car door Control Module Online Programming By X-431 PAD V

 

X-431 PAD V Online Programming】Benz S350 221Chassis Car door Control Module Online Programming operation method.

If you want to know more about X431, please click here: How to use launch X431.

Actual Measurement:
Benz S350,2005,VIN=WDDNG56X95A0*****,see pic1;

Function Description:
1.When replaced the new car door control unit module , need to execute this function.
2.When car door control unit cannot use normally, Maybe need to execute this function.
3.When updating and upgrading the car door control unit, need to execute this function.

Note:
1.Before executing this function, need to make sure the vehicle battery voltage not less than 12Vand the device electrical quantity is adequate. When executing programming ,device should connect internet.
2.When executing this function ,do not abnormally interrupted .Otherwise, it will cause car door control unit not be used and some serve consequence.
3.Please do not ignore any prompts when coding.

Operation Procedure:
1.Choose Benz V48.20 above;
2.Choose auto-search;
3.Choose car door control unit function;
4.Choose control module programming function;
5.Note the condition of control module programming executing .see pic2

6.After the confirmation condition is satisfied, the corresponding programming configuration file is downloaded from the network, and the network is needed to keep the network unblocked, as shown in figure 3;

7.After the configuration file is downloaded, the control unit software version information and programming function execution conditions will be displayed, as shown in figure 4;

8.The programming operation is to code the control unit. If the action fails, the control unit module cannot be used properly. Click “yes” to start the programming operation, as shown in figure 5;

9.Before implementing control unit programming, be sure to turn on the ignition switch, as shown in figure 6;

10.The programming interface shows the filename and programming progress that needs to be configured. The programming time may be longer. Please wait patiently, as shown in figure 7.

11.After the prompt coding has been successfully completed, the device will automatically complete the reset of the control unit module, as shown in figure 8, and the online coding has been completed.

https://www.obd2tool.com/blog/2021/03/02/benz-s350-221chassis-car-door-control-module-online-programming-by-x-431-pad-v/

Comments

Popular posts from this blog

VAG OBD Helper Software

VAG OBD helper 4th Immo Data Calculator free download source and installation guide. VAG OBD helper free download source: https://mega.nz/#!gZJzTKTC!BTVJqa-SmWgrwbd-n0vV8r2glx23d3l2OpN3ZRu1gXU Download the above link on the desktop. Decompress it. Install the driver firstly, then use the USB port to connect the device. Open the software, you will see the serial number read by the cable, the language is Chinese and English. There are some pdf files in Chinese on how to use VAG OBD helper to read out the 4th IMMO data and then use the key programmer to program key. VAG OBD helper Token: Each time the user read out the IMMO data, it will cost one token. Usually the VAG OBD helper comes with one free token FROM www.obd2tool.com , after it use up, just send the supplier serial number to charge more.

Solved BMW ISTA error IFH-0010, Vehicle could not be identified

This blog list 3 kinds of  bmw diagnostic scanner ISTA errors and solutions you may need. ISTA NCS error IFH-0010+ solution ISTA error”MSVCP120.dll is missing”+ solution ISTA error “The vehicle could not be identified”+ solution Note: All error solutions here are suitable for  BMW ICOM A2 and BMW ICOM Next ! ISTA error IFH-0010: DATATRANSMISSION TO CONTROLUNIT DISTURBED ISTA error: A communication fault occurred during activation Incorrect state: ERROR ECU CONDITIONS NOT CORRECT OR REQUEST SEQUENCE ERROR Solution: Try setting COM port latency to 1 in Advanced Settings for the port. You should change it to 1 to have the least lag/disturbances between data transfer. BMW ISTA System error “MSVCP120.dll is missing” The program can’t start because MSVCP120.dll is missing from your computer. Solution: Reinstall VC++ Redistributables and try again. If you’re running x64, you will need both x86 and x64 bit versions installed. Feedback: I got rid o...

How to Install Mercedes Benz DTS Monaco 8.16 Software

  This instruction show you the guide on how to install Mercedes Benz DTS Monaco Software . Preparations: Benz DTS Monaco Software Free Download After finish downoading and extract you will get below files Double click DTS-Setup to start installation Then just click default option to continue Click Finish Copy files in the repalce folder to DTS Monaco installation folder replace C:\Program Files(x86)\Softing\Diagnostic Tool Set 8\8.16\bin Then run “DTS Monacon” icon on desktop,it will show you the HWID and ask you to activate Please sent me your HWID to me(sales@obd2tool.com),we will sent you a activate file and license file When you get the xxx.reg file,doulbe click it to register it to your pc,click yes to add it the registy Run DTS Monaco and select “Administrate and manage DTS projects’ Select “System”–>”Add license” Load the License_0000000000000.bin file i sent you before Now your DTS Monaco have activated successfully! DTS Monaco 8.03.12 Softw...