Skip to main content

Reset Airbag by Digimaster 3

 

As we know, Yanhua Digimaster 3 can support automotive odometer adjustment, ECU, Airbag ECU data adjustment, computer program matching, audio decoding, automotive memory programming and key programming. Here mainly share the guide to reset Airbag and control computer data.

How-to-reset-Airbag-by-Digimaster-3-1

How to reset Airbag by Digimaster 3?

Note: After airbag detonation,the error record will be saved in the memory code of circuit board by airbag ECU. If you write the data generated before detonation when the computer hard disk not destroy, then you no need to change the circuit board.

Step1: Enter the Airbag Resetting interface

Choose the relevant model

Here we take Toyota as example

Step2: The airbag will be showed in list by number

Take “Toyota89170-06340” as example

How-to-reset-Airbag-by-Digimaster-3-2

Find out the chip in airbag ECU according to the diagram

Then dismantle the chip to install to OBP adapter, click “next step”

How-to-reset-Airbag-by-Digimaster-3-3

Step3: After finish reading data, it will prompt you whether need to restore airbag

Click “next step”, the data will be restored to airbag chip
How-to-reset-Airbag-by-Digimaster-3-4

2.How to reset Control Computer data by Digimaster 3?

Step 1: Enter “ECU” main menu

Select the corresponding car model

Here take “Passat B4” for example

How-to-reset-Airbag-by-Digimaster-3-5

Step2: According to the diagram

Dismantle the chip and install to ICP Adapter

Click “next step” to go on

Step3: After finish reading data, it will prompt that “it will cover the engine computer data”

then click “next step” to write data into the engine computer

How-to-reset-Airbag-by-Digimaster-3-6

Step4: After all these operations, just need to put the chip back to car

Digimaster III Odometer Correction Master Airbag Resetting Car Model Full List:

http://forobd2tool.com/wp-content/download/Digimaster_3/digimaster_iii_newest_car_list.pdf

Car models: Audi, Chrysler, Citroen, FIAT, Ford, GM, Honda, Hyundai,KIA, Land Rover, Mazda, Mitsubishi, Nissan, Opel, Peugeot, Renault, SSangYong, Subaru, SUZUKI, Toyota, Volkswagen, Samsung, MG Rover, Cadillac and Luxgen.

Please kindly notice: Here is not full car models Digimaster III supported, the car models always have been updating…

Labels:

Comments

Post a Comment

Popular posts from this blog

Solved BMW ISTA error IFH-0010, Vehicle could not be identified

This blog list 3 kinds of  bmw diagnostic scanner ISTA errors and solutions you may need. ISTA NCS error IFH-0010+ solution ISTA error”MSVCP120.dll is missing”+ solution ISTA error “The vehicle could not be identified”+ solution Note: All error solutions here are suitable for  BMW ICOM A2 and BMW ICOM Next ! ISTA error IFH-0010: DATATRANSMISSION TO CONTROLUNIT DISTURBED ISTA error: A communication fault occurred during activation Incorrect state: ERROR ECU CONDITIONS NOT CORRECT OR REQUEST SEQUENCE ERROR Solution: Try setting COM port latency to 1 in Advanced Settings for the port. You should change it to 1 to have the least lag/disturbances between data transfer. BMW ISTA System error “MSVCP120.dll is missing” The program can’t start because MSVCP120.dll is missing from your computer. Solution: Reinstall VC++ Redistributables and try again. If you’re running x64, you will need both x86 and x64 bit versions installed. Feedback: I got rid o...
Post a Comment
Read more

How to Solve VW Amarok Caddy 2018+ Remote Not Working After Programming

Here comes the general problem of VW Amarok Caddy etc. 2018+ UDS protocol vehicles: 2019 VW Caddy. I spent a few hours programming the Xhorse key using VVDI2 . Also tried TDB1000. Remote function could not be obtained. Every time the programming failed, the original remote stopped working until I scanned and cleared errors. I expected it to work when the transponder was added (Megamos AES). I can’t access remote learning with any of my tools, nor did vvdi2 let me program the remote. I was wondering if anyone could confirm remote learning with transponders or how to learn it if not. Solution: It is not possible for BH remote controls after 2018 at the latest. You will not get any communication with the central locking remote control customization. You need a dealer key 100% and then learn from ODIS. There is no after-market solution, VAG blocked the remote channel on UDS vehicles 2018+. Had the exact same issues with new caddies. So merchant key and Odis ATM since the c...
Post a Comment
Read more

VAG OBD Helper Software

VAG OBD helper 4th Immo Data Calculator free download source and installation guide. VAG OBD helper free download source: https://mega.nz/#!gZJzTKTC!BTVJqa-SmWgrwbd-n0vV8r2glx23d3l2OpN3ZRu1gXU Download the above link on the desktop. Decompress it. Install the driver firstly, then use the USB port to connect the device. Open the software, you will see the serial number read by the cable, the language is Chinese and English. There are some pdf files in Chinese on how to use VAG OBD helper to read out the 4th IMMO data and then use the key programmer to program key. VAG OBD helper Token: Each time the user read out the IMMO data, it will cost one token. Usually the VAG OBD helper comes with one free token FROM www.obd2tool.com , after it use up, just send the supplier serial number to charge more.
Post a Comment
Read more